Pulling Eyelet-set Ø 7 mm/0,2756 in. with thread RTG Ø 6 mm, 3 pieces, stainless

Pulling Eyelet-set Ø 7 mm/0,2756 in. with thread RTG Ø 6 mm, 3 pieces, stainless

8.80 CHF

Pulling Eyelet-set Ø 7 mm/0,2756 in. with thread RTG Ø 6 mm, 3 pieces, stainless

8.80 CHFPulling eyelet SET stainless steel - Ø 7 mm with RTG Ø 6 mm thread. Compatible with RUNPOTEC POWER REX, fiberglass rods Ø 4.5 mm and 6 mm Scope of supply: 3 x Pulling eyelet Ø 7 mm with thread RTG Ø 6 mm
Coupling joint-Set GF3 - Ø 3 mm/0,1181 in., 3 pieces, stainless

Coupling joint-Set GF3 - Ø 3 mm/0,1181 in., 3 pieces, stainless

8.60 CHF

Coupling joint-Set GF3 - Ø 3 mm/0,1181 in., 3 pieces, stainless

8.60 CHFServes as a connecting piece for POWER REX fiberglass rods Ø 3 mm, which can be bonded with the RUNPOTEC special adhesive or to repair any fractures. Made of stainless steel Scope of supply: 3 x Coupling joints GF3 - Ø 3 mm
Pulling grip - for fiberglass rod Ø 3 - 6 mm/0,1181 - 0,4724 in., non-slip

Pulling grip - for fiberglass rod Ø 3 - 6 mm/0,1181 - 0,4724 in., non-slip

7.90 CHF

Pulling grip - for fiberglass rod Ø 3 - 6 mm/0,1181 - 0,4724 in., non-slip

7.90 CHFPulling aid - handle for better gripping of the respective fiberglass rod. The pulling aid is ideally suited to push or pull all RUNPOTEC pull-in systems. The shaft in the grip increases friction by compressing and thus increases the advance or pull. Improves the holding grip for fiberglass rods Ø 3 - 6 mm, also suitable for RUNPO 1 and RUNPO 5. Material: anti-slip rubber Scope of supply: 1 x Pulling grip
Special glue 3 g, 1-component adhesive

Special glue 3 g, 1-component adhesive

11.00 CHF

Special glue 3 g, 1-component adhesive

11.00 CHF3 g special adhesive for repairing 3 mm, 4.5 mm and 6 mm fiberglass rods. The SPECIAL ADHESIVE from RUNPOTEC is very economical. One drop is sufficient for approx. 3 to 5 cm² of adhesive surface. For instructions see safety data sheet! Scope of supply: 1 x Special glue 3 g
Pull loop Ø 2 mm/0,0787 in. - with thread RTG Ø 6 mm, Loop length: 50 mm/1,9685 in., stainless steel

Pull loop Ø 2 mm/0,0787 in. - with thread RTG Ø 6 mm, Loop length: 50 mm/1,9685 in., stainless steel

8.70 CHF

Pull loop Ø 2 mm/0,0787 in. - with thread RTG Ø 6 mm, Loop length: 50 mm/1,9685 in., stainless steel

8.70 CHFPractical as a fixing variant, e.g. for attaching cable pulling grip (sock), ropes, cables etc. Alternative to eyelets => higher cable capacity. Suitable for POWER REX, RUNPOSTICKS, fiberglass rods Ø 4.5 mm and Ø 6 mm. Scope of supply: 1 x Pull loop Ø 2 mm with RTG Ø 6 mm thread
Pull loop Ø 1,5 mm/0,0591 in. - with thread RTG Ø 6 mm, Loop length: 85 mm/3,3465 in., stainless

Pull loop Ø 1,5 mm/0,0591 in. - with thread RTG Ø 6 mm, Loop length: 85 mm/3,3465 in., stainless

8.70 CHF

Pull loop Ø 1,5 mm/0,0591 in. - with thread RTG Ø 6 mm, Loop length: 85 mm/3,3465 in., stainless

8.70 CHFPractical as a fixing variant, e.g. for attaching cable pulling grip (sock), ropes, cables etc. Alternative to eyelets => higher cable capacity: Suitable for POWER REX, RUNPOSTICKS, fiberglass rods Ø 4.5 mm and Ø 6 mm. Scope of supply: 1 x Pull loop Ø 1,5 mm with RTG Ø 6 mm thread

<< < 1 2 > >>